Bizarre Patents
Wearable Device For Feeding and Observing Birds and Other Flying Animals
A device for feeding and observing flying animals comprising a hat, a support mounted on the hat and extending outward from the hat, and a feeder mounted on the support.
PatentStorm News
Make the Most of Our Site
See this month's Top Inventors and Most Cited Patents.
Stay on top of the latest innovations by subscribing to an RSS feed.
Registered users: Manage your profile.
| Number | Title | Issue Date |
| 7981333 | Method of setting mold clamping force of injection molding machine Test molding is performed by sequentially clamping a mold 2 with a mold clamping force (100%, 80%, 70%, . . . ) obtained by sequentially lowering a mold clamping force by a predetermined amount from the maximum mold clamping force (100%); with mold position s... | 07/19/2011 |
| 7943069 | Method of setting mold clamping force of injection molding machine When test molding is performed by sequentially clamping a mold with a mold clamping force (100%, 80%, 70%, . . .) obtained by sequentially lowering a mold clamping force by a predetermined amount from the maximum mold clamping force (100%), a mold clamping pressure ... | 05/17/2011 |
| 7938994 | Method of controlling an injection molding machine In a method of controlling an injection molding machine M which controls specified operational processes in a molding cycle by variably controlling the rotation speed of a driving motor 3 in a hydraulic pump 2 and driving a specified hydraulic actuator... | 05/10/2011 |
| 7914716 | Measurement control method of an injection molding machine A measurement control method uses an ending target position Xes calculated by adding a prescribed length Ls to a measurement ending position Xe. A rotation rate pattern Ar for rotating a screw 2, a back pressure Ps in relation to the screw 2, and a ret... | 03/29/2011 |
| 7896637 | Injection molding machine When constructing an injection molding machine M that is equipped with hydraulic pumps 2, which control discharge flow rates by variably controlling the number of revolutions of a drive motor 3, and that drives hydraulic actuators 4a . . ... | 03/01/2011 |
| 7892463 | Mold clamping force correction method for mold clamping apparatus When variation of mold clamping force to a mold C in production is detected and the mold clamping force is corrected on the basis of the detected variation, a work load accompanying high-pressure mold clamping of a mold clamping process is used as the variation, a w... | 02/22/2011 |
| 7846358 | Method of controlling injection molding machine When the number of rotations of a drive motor (3) driving a hydraulic pump (2) is variably controlled and thus each operation process in a molding cycle is controlled, as the hydraulic pump (2), a hydraulic pump (2) that can set at least ... | 12/07/2010 |
| 7866970 | Hydraulic drive device for injection molding machine In a hydraulic drive device (1) for an injection molding machine (M) that has a pressure control valve (Vs) incorporating a pressure sensor (2) for detecting a hydraulic pressure and a feedback control circuit (Cs) for controlling the hydraulic pressur... | 01/11/2011 |
| 7858017 | Material melting and holding apparatus of metal molding apparatus and rod material melting method There is provided a method for melting a material rod in a material melting and holding apparatus of a metal molding apparatus where the material melting and holding apparatus provided for the metal molding apparatus includes a furnace body of a melting and holding ... | 12/28/2010 |
| 7837811 | Method for manufacturing a composite of carbon nanomaterial and metallic material The present invention provides a method for manufacturing a composite of a carbon nanomaterial and a metallic material which has a homogeneous composite metal structure and thixotropic properties by compositing a metallic material of a non-ferrous metal alloy with a... | 11/23/2010 |
| 7833378 | Method for manufacturing optical disc and optical disc A method of manufacturing an optical disc includes molding a first disc substrate by a first mold simultaneously with a second disc substrate by a second mold while controlling the temperature of the first and second molds by passing a temperature-controlling medium... | 11/16/2010 |
| 7798799 | Measurement control method of an injection molding machine An ending target position Xes corresponding to the measurement ending position Xe, a rotation rate pattern Ar to rotate a screw 2, and a hypothetical retraction rate pattern Ab for the screw 2 to retract are set in advance, the remaining rotation rate ... | 09/21/2010 |
| 7749426 | Method for controlling molten metal material leaking in injection apparatus of metal molding apparatus A method for controlling a molten metal material in an injection apparatus that includes a cylinder body with a nozzle at a front end, and a discharge opening on a bottom side of a rear portion. Heating means are provided on an outer periphery of the cylinder body a... | 07/06/2010 |
| 7628300 | Method for preventing leaking of molten metal in injection molding of metal material A method of preventing leaking of molten metal from a nozzle in an injection apparatus comprising, metering the molten metal by travel of a plunger head backward from a most forward position to a most backward position at the rear of a supply opening while maintaini... | 12/08/2009 |
| 7578952 | Method for preventing backflow of resin in injection apparatus Leak of a metered resin by backflow in injection filling is prevented not depending on reverse rotation of a screw but by closing a ring valve by controlling a screw forward movement speed in injection filling. An injection filling speed and a valve closing operatio... | 08/25/2009 |
| 7462388 | Conductive resin molded product having insulating skin and method for forming the same The present invention relates to a conductive resin molded product having an insulating skin produced by a composite comprising a non-conductive resin and conductive material. The invention also provides a method for producing the conductive resin molded product. | 12/09/2008 |
| 7391336 | Anomaly monitoring system for molding machine Each of molding machines has a conductive line whose electrification state changes as a result of anomalous stoppage. An anomaly monitoring system includes detection sections provided in the conductive lines so as to detect the electrification states thereof; a data... | 06/24/2008 |
| 7343959 | Pressure casting method of magnesium alloy and metal products thereof The present invention provides a pressure casting method of a magnesium alloy. In the method, a molten magnesium alloy is cooled to form a partially molten state containing a solid-phase, and the partially molten state is further cooled to form a solid-phase granula... | 03/18/2008 |
| 7331372 | Method for melting metallic raw material in metal molding apparatus To insert a cylindrical metallic raw material into a melting cylinder provided in a heating holding cylinder of a metal molding apparatus and to efficiently semi-melt or completely melt the cylindrical metallic raw material, a clearance between an inner circumferent... | 02/19/2008 |
| 7303712 | Method of injection molding and compressive decoration molding a molded product Injection molding of a product and compressive decoration molding of a surface of the molded product are performed using individual cavity molds. A decorative film can be molded efficiently with a thermosetting coating material under suitable temperature control reg... | 12/04/2007 |
| 7303381 | Device for manufacturing optical disc, method of manufacturing the same, and optical disc In an optical disc molding device, a heating medium from a low-temperature controller is made to flow in temperature controlling flow passages (passages 3a) formed at locations corresponding to boundary parts of two fixed molds 7 mounted paralle... | 12/04/2007 |
| 7294302 | Method for controlling thickness of skin layer of composite resin molded product To control the thickness of the skin layer of a composite resin molded product by a viscosity difference obtained by varying the viscosity by adding another ultra-minute substance to a raw resin material. The composite resin molded product comprising the skin... | 11/13/2007 |
| 7267151 | Laminating apparatus When a laminating apparatus M is constituted with a vacuum suction step S1 for vacuum sucking an enclosed space in a work tray 2 accommodating a laminated-substrate W, a thermocompression-bonding step S2 for heating and pressuring the work tray ... | 09/11/2007 |
| 7244379 | Mold protection method for mold clamping apparatus In a mold protection method for a mold clamping apparatus, a predetermined mold protection zone is set in a zone in which a mold is closed, and an anomaly such as presence of a foreign object is detected on the basis of a change in a physical quantity in the mold pr... | 07/17/2007 |
| 7223093 | Coupling structure between injection driving screw shaft and electric motor in injection device A screw shaft for driving an injection screw driving body in a motor-driven injection device is coupled to a motor shaft of an electric motor in engagement of splines. A spline for the motor shaft engaging with a spline disposed at the outer periphery at a shaft end... | 05/29/2007 |
| 7223084 | Electric motor driven toggle mold clamping device The purpose of the invention is to prevent a sticking of lubricant to a ball screw shaft and a scattering to the circumstance in an electromotive toggle mold clamping device. This invention relates to the electric motor driven toggle mold clamping device wher... | 05/29/2007 |
| 7165599 | Melting and feeding method and apparatus of metallic material in metal molding machine In a metal molding machine provided having a tilt to a clamping device with an injection unit which is constituted by a liquid metallic material reservoir in which a cylinder having a nozzle portion at the tip portion equipped with a heating device at the outer peri... | 01/23/2007 |
| 7132068 | Mold closure position detection method for mold clamping apparatus In a mold closure position detection method, a mold closure position is detected on the basis of a variation in a physical quantity because of closure of a mold. The method comprises detecting an amount of movement of a movable platen, or a crosshead in the case whe... | 11/07/2006 |
| 7132067 | Mold-clamping control method for injection molding machine A mold-clamping control method for an injection molding machine includes the steps of detecting a value of a monitor item in a monitor region predetermined in relation to a mold closing operation in a mold clamping step; performing emergency processing when the dete... | 11/07/2006 |
| 7070724 | Composite-molding method and injection-molding machine of different material resin The present invention has an object of eliminating the holding pin trace of a composite-molding of the dichromatic molding by refilling with resin by the pushing pin and preventing the lateral-shift of the primary molding during the refilling. It is made possible to... | 07/04/2006 |
| 7041242 | Mold-clamping control method for injection molding machine The value of a monitor item is detected in a monitor region predetermined in relation to a mold closing operation during the course of a mold clamping step. Emergency processing is performed when the detected value exceeds a threshold value. There are preset an anom... | 05/09/2006 |
| 7036551 | Method of molding low melting point metal alloy The present invention relates to a method of molding a low-melting-point metal alloy which exhibits thixotropy properties in a solid-phase and liquid-phase coexisting temperature region. In this method, a temperature of a heating holding cylinder is increased to a l... | 05/02/2006 |
| 7032640 | Method of molding low melting point metal alloy A method of molding a low melting point metal alloy which exhibits thixotropy properties at a solid-liquid coexisting temperature, said method comprising the steps of heating said metal alloy at a temperature in the solid-liquid coexisting temperature region to form... | 04/25/2006 |
| 7013196 | Molding machine control system A control system for controlling the operation of a molding machine and its peripheral machines. This control system automatically transmits an advance notification of for example completion of production by the molding machine to an operator by electronic mail. The... | 03/14/2006 |
| 7004225 | Injection molding machine for low-melting point metallic material An injection molding machine for low-melting point metallic material has an injection mechanism having a melting cylinder, an injection device, and a driving device. The driving device is disposed on the rear end of the melting cylinder for driving the injection dev... | 02/28/2006 |
| 6999823 | Power shut-off method for injection molding machine Even when a power switch is turned off, the controller of an injection molding machine does not shut off a power supply immediately. The controller determines whether the present state of the injection molding machine is a previously-set confirmation-requiring state... | 02/14/2006 |
| 6971867 | Recovery apparatus of molded parts Thin and light molded parts released from a die are prevented from sticking by static electricity, by forming the recovery chute of molded part with fine wire gauze. The recovery receptacle 16, 17 for molded parts, molded parts introduction tube 23 and... | 12/06/2005 |
| 6917851 | Data printing method for injection molding machine A printer is connected to a printer connection section of an injection molding machine in order to print data regarding the injection molding machine. A controller of the injection molding machine has a printer judgment function for determining a type of the printer... | 07/12/2005 |
| 6913057 | IC-card manufacturing apparatus An IC-card manufacturing apparatus manufactures an IC card from a laminated substrate including an electronic component and laminate materials which sandwich the electronic component. The IC-card manufacturing apparatus includes a laminated-substrate sandwiching uni... | 07/05/2005 |
| 6915182 | Method for setting determination conditions used for determining whether molded product is non-defective or defective When a determination condition is set for determining whether a molded product is non-defective or defective, a molding operation is performed a predetermined number of times. In each molding operation, an actual value of at least one monitor item which can serve as... | 07/05/2005 |
